# Lab test torsion test

Check that the reading on the torquemeter is Angle of rotation of the 'driving' end for all load steps.

Firmly hold the three components together and tighten the cap screw D in the end clamp A. Turn the end clamp until the dial gauge plunger contacts the flat on the end of the rod H.

## Torsion of circular sections lab report

Set the dial gauge A to zero by rotating outer bezel. Parallax is an apparent displacement or difference of orientation of an object viewed along two different lines of sight. Scale readings for load steps up to just beyond the proportional limit when the tropometer is removed. Eg a tape measure is inaccurate due to temperature change, or it is actually printed wrong! Torsion tests can be performed by applying only a rotational motion or by applying both axial tension or compression and torsional forces. Using the following equations, calculate the shear strain and shear stress for each increment. Reset angle. This is not supposed to happen if you take the measurement carefully, but some meaurements are more difficult than others. Parallax error is an error caused by viewing the meaurement at an angle. Types of torsion testing vary from product to product but can usually be classified as failure, proof, or product operation testing.

As said earlier that stresses produce by the torque will be zero at central axis and maximum at the outer surface. Because we stop collecting scale readings slightly above the proprotional limit, you won't be able to get stress-strain data for the entire test.

### Lab test torsion test

Torsional shear stresses are maximum at outer surface ad minimum at the central axis. Set the dial gauge A to zero by rotating outer bezel. Slide the end clamp B onto the specimen and frimly tighten the cap screw D at the appropriate distance from the specimen and using the allen key set the rod H so that its radial support is at approximately 45 o from the vertical towards the handwheel side and tighten the knurled nut F to lock it in position. This is analogous to a force-displacement graph for a uniaxial test. Purpose of torsion testing: The purpose of a torsion test is to determine the behavior a material or test sample exhibits when twisted or under torsional forces as a result of applied moments that cause shear stress about the axis. First and third equation can be combined to an equation through which we can find the modulus of rigidity of any material under observation. A torsion test for failure requires that the test sample be twisted until it breaks and is designed to measure the strength of the sample. Be sure to only include data points up to the proportional limit when computing the regression. Firmly hold the three components together and tighten the cap screw D in the end clamp A. Check that the reading on the torquemeter is

Types of torsion testing vary from product to product but can usually be classified as failure, proof, or product operation testing. Determine the shear modulus G from the slope of the straight line.

### Bending and torsion test

During the experiment, if an adjustment is necessary, slacken the knurled nut F and reset the position of the rod H. This is analogous to a force-displacement graph for a uniaxial test. The fixed socket is attached to an instrument which senses torsional moment and displays this value on a graduated dial or digital torquemeter. The torsion testing device has two sockets, one fixed and the other can rotate. Load the straining head in position. Your lab manual has a good description of how this difference in readings can be used to compute the angle of twist over the specified gage length. Push one end of the specimen firmly into the socket mounted on the tailstock of the torsion machine. Materials used in structural, biomedical and automotive applications are among the more common materials to experience torsion in their applications. Add mass and measure angle.

The twisting force of a torsion test is applied to the test sample by anchoring one end so that it cannot move or rotate and applying a moment to the other end so that the sample is rotated about its axis.

After the device is removed, readings of load and angle of twist will still be recorded until failure.

Procedure We will apply a torsional force to a 19 mm diameter round metal sample and record the torque, angle of rotation, and angle of twist at several intervals.

Rated 10/10 based on 44 review